The window for the light hand fast operation method is the hard-core skill of driving technology. It is the content of assessing the level of driving. It is also sufficient for the car to save fuel. To experience the light foot and feet is to gently step on the accelerator pedal. Go to the light step and lift. Whether to lightly step on the accelerator pedal is related to the change of the opening degree of the carburetor throttle and the speed of the engine increase, and the time of operation of each device of the carburetor, which ultimately affects the steam. The size of the fuel consumption. Foot accelerator pedal Apricot lightly has a greater impact on fuel consumption, such as liberation, å® 090 type car, slamming on the accelerator pedal after starting, speeding up faster than the accelerator pedal, accelerating fuel consumption, increasing by about 3, lightly stepping on the accelerator pedal Fuel-saving, because the carburetor is the acceleration device Guo Yuzhi and the fuel-saving device, such as slamming the accelerator pedal, the acceleration device and the fuel-saving device will work in advance and provide additional oil. The mixture is too rich, resulting in the most fuel consumption of the car. When the car starts and shifts, the combination of the pedal and the accelerator pedal has a great influence on the fuel consumption. If the clutch is not engaged, the accelerator pedal is slammed. It will spin faster and waste fuel. If the clutch is engaged and the accelerator pedal has not been depressed, the engine will be turned off, or the engine will be forced to run due to the inertia of the car, equal to the engine brake, not only increase fuel consumption, but also clutch Accurate mismatch with the accelerator pedal to accelerate clutch wear, fast hand change quickly and shifting is timely, accurate and rapid, red connection affects fuel consumption and machine life, slow shifting operation, increase plant engine operation When called, it causes unnecessary power loss. If it is driving in a mountainous area or on a ramp, due to the delay of shifting the timing, the inertia of the car will disappear quickly, plus. The steam gravity point will not be 4 at this time, so it will start to increase the fuel consumption. When the car is driving uphill, the pedal can be stepped to the proper position; while the clutch pedal is depressed, the transmission lever is immediately moved to the neutral position. The position of the accelerator pedal is not moved. 3 The shift lever is hoisted to the new gear, and the clutch pedal is released until the clutch is fully engaged. However, during the entire process of rapid shifting, there is no intermittent time for the daughter-in-law. Hand and foot coordination should be coherent, the action should be coordinated, the shifting time is only 1 second and 2 seconds, which will shorten the shifting time, reduce the inertial force loss, reduce the oil, and obtain the oil-sucking effect of the Santana sedan. Synchronous hand-operated multi-stage gear transmission changer, with 4 forward gears and 1 to forward gears adopt lock-lock inertial synchronizer, and the shifting mechanism adopts full synchronizer meshing sleeve. It has a small quality structure and a reasonable layout. Work, reliability, n-life, etc., but if the operation and maintenance process is not operated in the correct way, the fault may occur at any time.
When the synchronizer is used correctly, when the two-leg clutch is used, the shifting and the downshifting, and the biting clutch is used, the method of adding and subtracting the gear when adding or subtracting the gear can reduce the circumferential speed difference between the phase-matching gears, thereby reducing the synchronization. The wear of the device and the extension of the synchronizer make it difficult to use the method of tapping the shift lever when the shift is performed. The main shift lever should always be pressed by hand. This ticket can be used to reduce the slip time of the synchronizer ring and reduce wear.
It is strictly forbidden to use the synchronizer to force the gear to start in the neutral flameout state. The motivation is because the engine's moment of inertia is very large, the synchronizer time is long, the sliding friction is increased, the temperature of the shackle ring is increased, and the synchronizer is easily burned. 4 It is strictly forbidden to keep the same cargo from the starter, that is, not to use the clutch and use the synchronous friction to stop the step control. Vehicle speed and brake gear precautions When the vehicle is stationary, the inch can be hanged.
When the engine is running, the clutch should be stepped on before shifting.
On the handle, otherwise the fork will wear prematurely. Correctly use the lubricating oil. When the Santana brake is delivered from the factory, the lubricating oil has been added to the transmission. Under normal circumstances, the lubricating fluid level of the transmission does not need to be checked but when it is running normally. 100,000 km, after 200,000 km, the secondary lubricant must be replaced. Santana car transmission is steep and sturdy, Tuanping hope, æ’¼è‹ Zhong Tong
According to regulations, live birds reception should be at the wind down area of the processing plant. Including parking area, slaughtering-waiting area, unloading ,live birds hanging, stunning and bleeding area, crates cleaning, crate pelleting,vehicle disinfection area,waste store ,reception and urgent killing area and so on. The slaughterhouse is appropriate to single layer, net height is not less than 4.2 meter, the polar space not less than 6 meter, hanging area is the main workshop bleeding room design to be darkroom which separate with our working area.Close to one side to receiving area is to be working area, including clearing room, official quarantine room, if have halal products, should with one rest room for Iman.
1.Live poultry vehicles should have special road. There is a disinfection pool which same wide as door at the entrance for live poultry enter..The pool size is about 3 meters long and 100 to 150mm deep.
2. UnloadingThe platform built which height is same as vehicles which save much labor. Two workers unloading crates from vehicle,each time unload 8 to 9 layer of crate, each hour unloading 12000birds. Normally unloading platform should be keep some crates. According to WSPA regulations, when live birds reach slaughterhouse should be killed within 1hour,max. Not more than 2 hours, for one slaughterhouse which to slaughter 12000birds/H, the parking place should be suitable for 5 trucks, unloading area is suitable for 2 trucks, crates pelleting area is suitable for 3 trucks, and with spare crates storage room to keep spare crates.
3. Live birding hangingThere should be a darkroom after birds hanging and stunning, the orbit of overhead conveyor line should be kept level,straight ,try to reduce the turns and movements; The overhead conveyor line with synchronous control system and emergency stop system to ensure the reliable running of the processing line. The appropriate shackles are used according to different type of poultry and raising period; Try to keep poultry appease to prevent wings injury from struggling to ensure meat quality.
Live Bird Receiving Unit, Chicken Hanging Unit, Live Bird Reception, Chicken Reception
Connect Group For Poultry Project , https://www.connectpoultry.com