With the accelerating pace of urbanization in China and the rapid increase of roads, people now have higher requirements on the quality of life and living environment. The relevant government departments attach great importance to the protection of the environment, so the urban affiliated units or enterprises are responsible for spraying vehicles. The needs of the people have gradually increased, but it has been found through investigation that many of the driver's friends may not promptly and effectively eliminate some minor malfunctions of the sprayer because they do not know much about the sprayer. For everyone to analyze some of the knowledge about the car sprayer troubleshooting, I hope everyone can use it later.
1. We must always fill the sprayer with water at the beginning of the operation. When the water is pumped, there may be a phenomenon that no water can be pumped. The reason for this may be because the pipeline is not tightly closed, the filter is too deep into the pool, or there is insufficient water diversion. For this we can look at the pad, adjust the thickness of the gasket or increase the amount of water diversion. Try putting the filter deep.
2. When we use the spray truck , we may still have a phenomenon that the spraying width is not enough. In this case, it may be due to the insufficient speed of the pump power, the incorrect spray angle, and the blockage of the piping system. It is not the above reason that the large throttle is used to eliminate power for its purpose, adjust the spray angle, and check whether the piping system is normal.
3. During the process of use, we may experience abnormal noises from the water pump or more severe vibrations. This may be due to the large distance between the bearings or gears of the water pump or the lack of lubricant in the gear box. Now. The driver's friend can add lube oil or the specification can be excluded based on the normal parameters of the pump.
4, in the process of use may also appear ball valve failure or malfunction, which may be due to the cylinder or the valve core damage caused, we can check the circuit or gas circuit operation is normal and Replace the spool to determine if it is the above reason.
The above is an introduction to the exclusion analysis of four common faults of spray trucks . I hope to help everyone.
Introduction Of Company
HBYM is a big supplier in china.We produce spare parts for Putzmeister, Schwing, Sany , Zoomlion etc . Products include: S valve, swing lever, outer housing, Plunger Cylinder , Upper Housing Assy, wear plate , cutting ring ,motor etc . We have a manufacture factory(Cangzhou Hongcheng Machinery Equipment Co., LTD) and a trading company(Cangzhou Xingwei International Trade Co., LTD) .So we can ensure the quality and delivery time.And we can give you a competitive price.
Advantages:
1,We can give you a competitive and detail price,when i receive your inquire.
2,If you have special need in surface and package,we can do as your need.
3,After you purchase from us,we will supply a superior service for you.
4,We had took part in many exhibitions,and get good reviews from colleagues.
If buyer need special model products, factory can produce as per buyer's drawing .
If you have need of concrete parts,Cangzhou Hongcheng Machinery Equipment is your best choice.
Putzmeister Concrete Pump Parts Description
|
|||
Putzmeister S Valve (Big Mouth)2318 C00179300 |
Putzmeister 90 Swinging Lever 274877001 |
Putzmeister Outer Housing 240391003 |
Putzmeister Plunger Cylinder C40224400 |
|
|||
Putzmeister For Plunger Cylinder (Big S Valve) |
Putzmeister 90 Upper Housing Assy 274893001 |
Putzmeister DN230 Wear Plate C00178700 |
Putzmeister DN230 Cutting Ring C00178600 |
|
|||
Putzmeister S Valve (Small Mouth)2018 251013008 |
Putzmeister 80 Swinging Lever 254424005 |
Putzmeister Outer Housing 24060004 |
Putzmeister Plunger Cylinder 262840008 |
|
|||
Putzmeister Seal For Plunger Cylinder (Small S Valve) |
Putzmeister 80 Upper Housing Assy 401783 |
Putzmeister DN200 Wear Plate C00137700 |
Putzmeister DN200 Cutting Ring C00137900 |
|
|||
Putzmeister Flap Elbow 417730 |
Putzmeister No.2 Elbow 292079001 |
Putzmeister Wear Sleeve 228383004 |
Putzmeister Mixer Shaft 275587002 |
|
|||
Putzmeister DN200 Piston 086236005 |
Putzmeister DN230 Piston 262893000 |
Putzmeister DN200 Piston Seal 080372004 |
Putzmeister DN200 Guide Ring 080794006 |
|
|||
Putzmeister Seal For Outer Housing |
Putzmeister For Mail Oil Cylinder | Putzmeister For 90 Upper Housing Assy | Putzmeister Seal For 80 Upper Housing Assy |
|
|||
Putzmeister Hydraulic Grease Pump | Putzmeister Electric Grease Pump | Putzmeister Manual Grease Pump | Putzmeister Oil Distributor |
|
|||
Putzmeister Hydraulic Motor OMH500 238130001 |
Putzmeister Conveying Cylinder |
Putzmeister Bladder 4L 6L 10L |
Putzmeister Hydraulic Pressure Gauge 017250005 |
|
|||
Putzmeister DN125 DN150 Snap Clamp | Putzmeister DN125 DN150 Bolt Clamp | Putzmeister Filter | Putzmeister Battery |
There are many other brands on sales:
1)Schwing Concrete Pump Parts;
2)Zoomlion Concrete Pump Parts;
Package&Delivery
1)Package:Wooden Packing
2)Delivery Time:5-12 Days(After receive advance payment)
FAQ
Q: Are you trading company or manufacturer ?
A: We are factory.And we have a trading company,so we can give you a competitive price.
Q: How long is your delivery time?
A: Generally it is 5-10 days if the goods are in stock. or it is 15-20 days if the goods are not in stock, it is according to quantity.
Q: Do you provide samples ? is it free or extra ?
A: Yes, we could offer the sample for free charge but do not pay the cost of freight.
Q: What is your terms of payment ?
A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 30% T/T in advance ,balance before shippment.
Putzmeister Spare Parts,Mixer Shaft,Piston Seal,Remote Battery
HBYM GROUP Co,.LTD , https://www.hbympumpparts.com